The Ultimate Guide To h335 308 load data
The Ultimate Guide To h335 308 load data
Blog Article
I began capturing Pdogs with tac. Shot excellent and everything things. The subsequent 12 months, I couldn't find any so I checked the burn off charts and here is H335. Tried out it and acquired the EXACT same pace with the EXACT same powder cost of tac.
My knowledge with CFE223 is basically very good velocity for just a provided load when compared with other powders, but mediocre accuracy.
Horn, I have tried using 50gr. H380 to get a 165gr Hor. awhile back again, fifty two remaining the max. but you actually must pack that bullet in there With all the max load, but I did get pretty good accuracy with it, 3/four" @a hundred I think it had been, from the 700V, but if you do not treatment about fitting the spherical inside your mag.(solitary shot) seat the bullet about .010' from the lands like I claimed before and also the bullet won't be so packed in there so limited, which I guess definitely Do not harm almost nothing, given that it goes in.
I unquestionably will not advocate EVER exceeding analyzed reloading manual data and now I will include the analyzed handbook data should be from your bullet producer’s handbook, not data for generic bullets.
My load with Hornady fifty five-gr bullets was wonderful, but his Along with the Noslers (in a Rem seven-hundred VS) wasn't. Very hot temps + a bullet that tends to produce far more tension + unique rifle. Backing off at least 0.5 to 25.five or considerably less would resolve his stress issues. In the situation of anyone working with Federal .223 Rem brass that's been observed for causing pressure troubles resulting from it's thicker partitions and thinner Website space, a minimized load is surely proposed. That is why some posters have unique effects with loads that are merely fine for Some others. Nearly all handloaders who definitely have no way of chronographing their get the job done-ups like a way of acquiring a handle on tension of their guns with their factors. When pressure indications seem around the brass and/or primer, then regretably excessive force is by now existing. Keeping track of the chronograph average velocities lets you are aware of when predicted greatest velocity has actually been reached. In such cases It might be in the region of 3107 fps in the event you normal out all 5 sources. Therefore backing off a little bit will Typically keep away from this and is working with good perception. 1 good way of obtaining a good cope with on what your limitations needs to be is to average data from each of the sources you can get. In such a case, averaging all 5 sources presents an average most demand fat of 25 grains at 3107 fps. Should you had been to throw out the "odd" utmost charge bodyweight of Hornady as well as "odd" minimal velocity of Sierra you should get this regular: 25.5 grains at 3134 fps - which I believe would be a little additional sensible figures for barrels within the 20-22" range from what I've observed. Which is why I like to refer to as several data sources as is possible in advance of placing aims for just a load work-up. On top of that, just one should really study and find out If your picked parts can add to force (Federal .223 brass, Nosler Ballistic Ideas, M193 bullets and so forth.) Obviously this discussion is just not about discovering your "accuracy node" but just charge/tension/velocity ambitions or ceilings. Nonetheless in my case, accuracy seems to extend with will increase in charge excess weight when loading H-335. Commence loads like 23 to 25 grains are only so-so, but loads like 25.five are Great for me. I believe the bullet made use of helps make A much bigger variance compared to demand body weight. *While some Take note that 26.0 grains is usually a "5.56 NATO-force" load - On this particular scenario it is clear that true five.fifty six NATO-tension ammo - LC M193 truly is far hotter and 90 fps quicker In this particular unique AR15. This can only be established from the chronograph or even a stress barrel.
Concerning restrictions, CFE 223 is fairly rapidly burning for any rifle powder. Subsequently, it might not function very best with heavier bullets in some cartridges, and will not be appropriate for Magnum rifle scenarios.
LIL'GUN® - State-of-the-art technology propellant style and design just for the 410 BORE. The 410 shotshell has lengthy been tricky to load due to shortcomings in powder healthy, metering, and burning attributes.
Due to similarities concerning the .308 and the 7.62x51mm cartridges, There's been some confusion concerning primer preference. For instance, the seven.62x51 is loaded with a substantial rifle magnum primer, like the CCI No. 34. A number of the reasoning for utilizing this comparatively incredibly hot primer involves trusted ignition with spherical powders under all temperature extremes.
I have a Hornady electronic powder evaluate/scale I use for the tough powders (like IMR4198 - my preferred .223 powder for smaller groups) that just will likely not toss regular costs via a powder evaluate.
Of course, I flew Cobras in the Army and the truth is couple of men and women close to have fired read more as quite a few rounds in anger as I've. I acquire that company Quite severely. ETA: I have also been reloading for more than twenty five years and possess reloaded A large number of rounds in 8 diverse calibers and not using a one failure or overpressure. I'm not a rookie.
Sign up for the special reloading community Started in 1996 and be the initial to find out about our latest news, reviews, and insights.
Include to quote Only clearly show this person #ten · Nov twenty five, 2014 I question greatly that I have a clue of your forty decades encounter with reloading, I'm very much a newbie but genuinely wish to reload and study, I believe I will relieve up the ladder using this facts and retain an in depth eye on items and may endeavor to Permit yea understand what I think of or how it works out, if the rain at any time stops down listed here,,, it has been pouring for 3 times....
2 grains instead of exceed 3100 fps. The outcomes posted during the guide for a longer barrel do produce increased values, but it would appear that the worth of your NATO ammunition in that barrel would produce even greater values.
Quick forward a number of years with a different new bolt action .223 and that same load was providing me cratered primers and challenging to eject brass.